Automation-components Separate Input w/RJ12 Phone Jack Uživatelský manuál stáhnout pdf

Installation and Operation Instructions

Separate Input w/RJ12 Phone Jack

2305 Pleasant View Rd. Middleton Industrial Park Middleton, WI 53562

PH: (608) 831-2585 FAX: (608) 831-7407

II-9

utomation

omponents

nc.

READ THESE INSTRUCTIONS BEFORE YOU BEGIN INSTALLATION

All ACI thermistors and RTD temperature sensors are both non-polarity and non-position sensitive. All thermistor type

room units are supplied with a two-pole terminal block and all RTD’s can be supplied with either a two or three-pole

terminal block.

All of the following units are available with corresponding terminal blocks for all connections: Rooms with Setpoint (RS),

Rooms with Override (RO), Rooms with Setpoint and Override (RSO), and Rooms with Setpoint, Override, and RJ12

Communication Jack (RSO RJ12).

**Note: All Room with Override (RO) and Room with Setpoint and Override (RSO) sensors are shipped with the

 Override in Parallel with the sensor unless specified otherwise. If a Separate Input or Tenant Override is

 Needed, see Figure #1 for the Override Options Jumper Settings.

All other configurations are supplied with 22 gauge lead wires and can be hooked up with any crimp style or wire nut wire

connectors. ACI recommends the use of 18 to 22 AWG twisted pair wires or shielded cable for all sensor installations.

n TROUBLESHOOTING

Sensor reads 0 ohms or very low Sensor or wires are shorted together

Sensor reads infinity or very high Sensor or wires are open

Erratic readings Bad wire connections - Condensation or Moisture problem

nWIRING DIAGRAMS

Short Sensor

arate In

SW1

Gnd + - S E T O / R

1 2 3 4 5 6

6 Pin RJ12

Communication Jack

Thermistor and Override

Out

ut to Controller

Thermistor and Override

Out

ut to Controller

Setpoint Output to Controller

Tenant Override (Dry Contact) Output

to Controller

(Se

arate In

ut Onl

)

Tenant Override (Dry Contact) Output

to Controller

(Se

arate In

ut Onl

)

Terminals for RJ12 Communications

Membrane

Wire Access Hole

“After Hours” Normally-Open

Override Switch

Override Options Jumper Settings (J3)

Short Sensor Short Sensor

Separate Input

Override Shorts Separate Input

Sensor (Dry Contact Closure

)

Figure #1

arate In

** NOTE: (J2) is only used for Connection of the Membrane Switch.

*** NOTE: When wanting to use a Single Common for all (3) of the Outputs on a Separate Input Sensor,

 connect one wire in series with one of the Sensor, Setpoint, and Override Terminals. These three

 terminal may then be tied to the common of the controller with one wire, while the other three

 terminals would need to be connected to the proper Sensor Inputs of your controller.

Multi6 Rev 7

1 2

Contact Closure 1

Shrnutí obsahu

Strany 1 - Contact Closure

Installation and Operation Instructions Separate Input w/RJ12 Phone Jack 2305 Pleasan

Strany 2

2305 Pleasant View Rd. Middleton Industrial Park Middleton, WI 53562PH: (608) 831-2585 FAX: (608) 831-7407 II-10 Figure #2 8’, 12’, or

Komentáře k této Příručce

Žádné komentáře

Automation-components Separate Input w/RJ12 Phone Jack Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Teploměry Automation-components Separate Input w/RJ12 Phone Jack. Automation Components Separate Input w/RJ12 Phone Jack User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Teploměry Automation-components Separate Input w/RJ12 Phone Jack